MagnaFlow install
Hey all,
I purchased online and took delivery of a set of those plastic car ramps rated for 8000 pounds. Will these and jacking up the ass end allow me to remove the old stock and install the new MF system? I'm hoping it takes only a couple hours to do it. Thoughts? Experience?
I was thinking if I needed to I could put the ramps on some boards to get a couple more inches out of them. No hoist so making the most out of a poor situation and trying to save myself the $$ by doing it meself!!
2009.5 MSM GXP 500ish N/A RWHP. Mods include but aren't limited to: Texas Speed 418 (6.8L) fully forged held together with ARP from top to bottom, PRC 255cc heads, Rick Crawford intake plenum, TB port, polish and tune, Roto-Fab 102mm CAI w/LS7 MAF, Kooks 1-7/8" headers wrapped with DEI, Corsa catless system, Circle D 3200 Stall, 3.45 final drive, BMR's complete street bushing kit and sway bars, Eibach Pro Kit, G-Force Axles, running on staggered VMR 710's with Bridgestone RE11 rubber. HSV triple gauge pack with Calais smokers kit mod, V6 tails, debadge/rebadge, V6 door handles, AU black door trim, Maverick Man under hood strut covers, & washer and bolt kit, fully corrected paint thanks to Adams Polishes and my hard work. Built with reliability in mind with some power for those times when you need to pass or go over a big hill. Just a poser, not a racer!
Back on to the ramps. Face down ass up, this is the way we like to.............install MagnaFlow. LOL
2008 Liquid Red Pontiac G8 Sport/Premium - Adams Polishes - American Racing Headers - ARP - BMR Fabrication - Circle D Specialties - COMP Cams - Crazy Paul - Dynojet - Earl's - Flowmaster - Fuel Air Spark Technology - G2 - GFORCE 1320 - Greg Weld - HP Tuners - JBA - Lingenfelter - Maverick Man Carbon - Metco Motorsports Solutions - Mickey Thompson - M&H - Mike Norris Motorsports - NGK - Pace Performance - Pedders USA - Powerbond - PSI - Russell - SBX Performance - SJM Manufacturing - SPOHN Performance - Tony Mamo - Vararam - Vector Motorsports - Wretched Motorsports - 470 RWHP 427 TQ - Engine Tune By Patrick G
So jack up the front then and use the ramps in back?Originally Posted by GRRRR8
Could just work...
2009.5 MSM GXP 500ish N/A RWHP. Mods include but aren't limited to: Texas Speed 418 (6.8L) fully forged held together with ARP from top to bottom, PRC 255cc heads, Rick Crawford intake plenum, TB port, polish and tune, Roto-Fab 102mm CAI w/LS7 MAF, Kooks 1-7/8" headers wrapped with DEI, Corsa catless system, Circle D 3200 Stall, 3.45 final drive, BMR's complete street bushing kit and sway bars, Eibach Pro Kit, G-Force Axles, running on staggered VMR 710's with Bridgestone RE11 rubber. HSV triple gauge pack with Calais smokers kit mod, V6 tails, debadge/rebadge, V6 door handles, AU black door trim, Maverick Man under hood strut covers, & washer and bolt kit, fully corrected paint thanks to Adams Polishes and my hard work. Built with reliability in mind with some power for those times when you need to pass or go over a big hill. Just a poser, not a racer!
You could, but you are only taking off 4 nuts up front. Everything else is in the rear.
2008 Liquid Red Pontiac G8 Sport/Premium - Adams Polishes - American Racing Headers - ARP - BMR Fabrication - Circle D Specialties - COMP Cams - Crazy Paul - Dynojet - Earl's - Flowmaster - Fuel Air Spark Technology - G2 - GFORCE 1320 - Greg Weld - HP Tuners - JBA - Lingenfelter - Maverick Man Carbon - Metco Motorsports Solutions - Mickey Thompson - M&H - Mike Norris Motorsports - NGK - Pace Performance - Pedders USA - Powerbond - PSI - Russell - SBX Performance - SJM Manufacturing - SPOHN Performance - Tony Mamo - Vararam - Vector Motorsports - Wretched Motorsports - 470 RWHP 427 TQ - Engine Tune By Patrick G
Posting Permissions
Reply With Quote