-
Junior Member
Front License Plate Mounting Options
It's time that I put a front plate on. Anyone have some new or interesting ways to do it? I want it to remain clean looking and not drill hole in the bumper if possible, but don't think I want a retractable one. Suggestions?
-
VIP Member
Duct Tape? Liquid Nails? C-Clamps? Velcro? Magic?
No screws, no retractable, which requires screws, not sure what you could use.
Kevin
2009 SRM G8 GXP A6 + Roof
Go
Vararam CAI
VMS "Stealth" Dyno Tune
VMS HSRK
GTPprix's hacked Atari gauges
Norris Motorsports Billet Oil Catch Can
Radical Advantage Trans dipstick
Blendimount and Invisicord for the V-1
Doug Thorley LT's
Show
Tint by Spade Kreations 35% & 20%
Holden V-6 rad cover courtesy of Crazy Paul
PB
12.986 @ 108.78
R.I.P. Charlie......FUCK Cancer!
-
I ordered and received one of these. I know you said you didn't want a retractable, but it truly is one of the best ways and can be hidden when it's unneeded.
http://www.amazon.com/gp/product/B00...?ie=UTF8&psc=1
2009.5 MSM GXP 500ish N/A RWHP. Mods include but aren't limited to: Texas Speed 418 (6.8L) fully forged held together with ARP from top to bottom, PRC 255cc heads, Rick Crawford intake plenum, TB port, polish and tune, Roto-Fab 102mm CAI w/LS7 MAF, Kooks 1-7/8" headers wrapped with DEI, Corsa catless system, Circle D 3200 Stall, 3.45 final drive, BMR's complete street bushing kit and sway bars, Eibach Pro Kit, G-Force Axles, running on staggered VMR 710's with Bridgestone RE11 rubber. HSV triple gauge pack with Calais smokers kit mod, V6 tails, debadge/rebadge, V6 door handles, AU black door trim, Maverick Man under hood strut covers, & washer and bolt kit, fully corrected paint thanks to Adams Polishes and my hard work. Built with reliability in mind with some power for those times when you need to pass or go over a big hill. Just a poser, not a racer!
-
Senior Member
Something like this may work though you may need to "massage" the lower grill a bit..
http://www.ebay.com/itm/New-JDM-Blac...ddb649&vxp=mtr
I was thinking you could bolt it up under the edge of the lower grill and just notch out the area on the grill where it needs to pass through.
Matt Jones
2009 WH G8 GT Vararam/Kooks LT's/Corsa/BLP Probationary LL 219/223 .612/.615 112LSA/3.45s
-
Junior Member
Originally Posted by
kevinm0131
Duct Tape? Liquid Nails? C-Clamps? Velcro? Magic?
No screws, no retractable, which requires screws, not sure what you could use.
I wouldn't mind drilling from the underside of the bumper just as long as I don't have hole in the front taking away from the looks.
Originally Posted by
Chewy
Thats but I guess my point is that it would never be unneeded so why bother?
-
Junior Member
Originally Posted by
mjones73
Something like this may work though you may need to "massage" the lower grill a bit..
http://www.ebay.com/itm/New-JDM-Blac...ddb649&vxp=mtr
I was thinking you could bolt it up under the edge of the lower grill and just notch out the area on the grill where it needs to pass through.
I must be a little slow this morning but I am having a hard time picturing how that would actually mount up. I saw someone else with some "L" brackets that mounted behind, and then through, the lower grills and relocated the plate to either side of the bumper. Waiting on more specific information from him.
-
Senior Member
Honestly not sure if it would work, just throwing ideas out there.
Check the other forum, there is a thread where someone fabricated brackets like you're describing.
Matt Jones
2009 WH G8 GT Vararam/Kooks LT's/Corsa/BLP Probationary LL 219/223 .612/.615 112LSA/3.45s
-
Junior Member
-
Originally Posted by
CMD
Thats but I guess my point is that it would never be unneeded so why bother?
I go to a lot of car shows and cruise in's so it'll get well used on my car. It mounts under the car so why reinvent the wheel?
2009.5 MSM GXP 500ish N/A RWHP. Mods include but aren't limited to: Texas Speed 418 (6.8L) fully forged held together with ARP from top to bottom, PRC 255cc heads, Rick Crawford intake plenum, TB port, polish and tune, Roto-Fab 102mm CAI w/LS7 MAF, Kooks 1-7/8" headers wrapped with DEI, Corsa catless system, Circle D 3200 Stall, 3.45 final drive, BMR's complete street bushing kit and sway bars, Eibach Pro Kit, G-Force Axles, running on staggered VMR 710's with Bridgestone RE11 rubber. HSV triple gauge pack with Calais smokers kit mod, V6 tails, debadge/rebadge, V6 door handles, AU black door trim, Maverick Man under hood strut covers, & washer and bolt kit, fully corrected paint thanks to Adams Polishes and my hard work. Built with reliability in mind with some power for those times when you need to pass or go over a big hill. Just a poser, not a racer!
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes
-
VIP Member
20150327_155033.jpg
I bought a cheap plastic frame back plate and a small back plate for spacing. Bolted them together with the small one on the bottom behind it and used foam tape to protect the paint. Mounted it with zip ties to the grill.
Last edited by Modhauler; 03-27-2015 at 12:03 PM.
09 SRM G8 GT &
09 SBM G8 GT