-
Wiring for triple gauge
It's probably posted here somewhere but I could not find it. I am looking for switched power and dash lighting for Autometer gauges (boost, fuel press., wideband) I am installing in a HSV triple gauge setup.
09 G8 GT MGM, Premium/Sport/Sunroof
TVS1900 Maggie w/3" pulley, Kooks 1-7/8 LT's, Magnaflow 16875 moded to full 3" exhaust w/hf cats, Fast 65# injectors, Lonnie' dual FP, Camaro 3.27 diff, Roto-Fab CAI, BP catch can, IAT relotation kit, Dynoed @ 485rwhp-475 rwtq
Homelink-visor, auto dim mirror, LED int. lights, driverside trunk release, HSV 3 gauge kit w/boost, fuel press., wideband, Kicker subs, Kappa 62.9i door speakers & tweeters, center speaker resistor, Damplifier
Spencer's HID low beams and fogs, LED lights with clear sidemarkers, 50% tint, clear bra, debadged, ASA wheels w/RE050A 285/35 rears
-
Moderator
2009 Karma Metallic G8 GT The best gift you can give to someone is your time,because you're giving them something that you can never get back
-
Post Thanks / Like - 2 Thanks, 0 Likes, 0 Dislikes
-
It's on the right side of the radio when you take the trim off. There is a false plug terminating the wires, but you can take that off. The wires available are +12V, ground, and GMLAN.
-
Addicted Member
Originally Posted by
igneon
It's on the right side of the radio when you take the trim off. There is a false plug terminating the wires, but you can take that off. The wires available are +12V, ground, and GMLAN.
Is that plug visible in this crappy pic?upper_connect..jpg
SOLD 2009
Panther Black G8 GXP #112 - M6
Scheming on my LSX Sequel...
-
VIP Member
The 12v outlet is switched. It's what I used but my gauges are mounted in the cubby.
08 G8 GT: MagnaCharger TVS MP1900 10psi, LS9 cam, 72# injectors, Roto-Fab CAI, SLP Headers, Corsa Catback, etc.
My Garage
-
Formerly HSV-GTS-300
-
VIP Member
CP sent me the same wiring help. I elected to tap into the BCM Pin 24 which is in the last print with the black dots. The lighting for my HSV gauges work perfect with the rest of the dash lighting. It is a little bit of a pain but it can be done. I just cut the wire and used spade connnectors with insulators.
09 G8 GXP A6 SRM with sunroof. Mods:Livernois magnacharger 2300, 3.0" pulley, 160 stat, KB Bap. Rotofab,Corsa, Kooks 1 7/8 mids. 502rwhp/479tq. Suspension: BMR , Pedders Supercar coilovers, all Brembos. Show:CTS-V rims w/nitto invos 255/40 and 285/35. HSV triple gauges & CP smokers pack
RIP Charlie.
-
Beyond Help
so i was trying to wire up my autometer boost guage and find a 12v source so it can be lit at night and i read this i connected it to pin 10 and it comes on and off with the ignition but is there another other wire that carries power to where it only turns on with the dash or headlamps? i tryed white and gy white and none of them worked besides pk and blue
Texas speed 408 stroker,Lingenfelter ls3 ported heads,tv1900,2.8 pulley,kooks header header back,custom axel back, squash double pump upgrade, e85 tein lowering , demon 8 triple pod, brembo brakes ,brm sway bar, bmr toe rod , bmr end link, spohn trailing arms, tein springs,tsw nurburgring rims. Icebox. Old numbers on stock engine 650/620 with 3.0 pulley
-
Formerly HSV-GTS-300
Originally Posted by
Darkmanx
so i was trying to wire up my autometer boost guage and find a 12v source so it can be lit at night and i read this i connected it to pin 10 and it comes on and off with the ignition but is there another other wire that carries power to where it only turns on with the dash or headlamps? i tryed white and gy white and none of them worked besides pk and blue
ILLUMINATION = PIN 8
& IGNITION1 VOLTAGE = PIN 10
both from Headlamp Switch.
Last edited by Crazy Paul; 06-20-2012 at 10:35 PM.
Crazy Paul
Your Holden Parts Connection in Australia!
-
Beyond Help
Originally Posted by
HSV-GTS-300
ILLUMINATION FROM BCM (not from Headlamp Switch).....read above and look at pics above.
WHITE WIRE for Illumination runs to Body Control Module (A15)
Connector X5 , sometimes also called J5.
PIN24 ...... (has White/Yellow Wire......Park Lamp Relay Control......Circuit 1080)
im not a wiring person so i was kinda lost i just wanted a do this and connect to this wire i dont even know where the bcm connects are
Texas speed 408 stroker,Lingenfelter ls3 ported heads,tv1900,2.8 pulley,kooks header header back,custom axel back, squash double pump upgrade, e85 tein lowering , demon 8 triple pod, brembo brakes ,brm sway bar, bmr toe rod , bmr end link, spohn trailing arms, tein springs,tsw nurburgring rims. Icebox. Old numbers on stock engine 650/620 with 3.0 pulley