-
VIP Member
07 Nitro Lean/Rich/Evap/o2/EGR
Guy in town here has a 2007 Nitro and asked me to give it a look. Id like some input on where to start, ie what to replace first.
p0171 Bank 1 Lean
p0172 Bank 1 Rich
p0456 Evap very small leak (his dash reads gas cap, but he has replaced the cap)
p1404 EGR closed performance
p0131 B1S1 o2 low voltage
I cleared the codes and will see what comes back over the next few days. Who knows how long the CEL has been on.
Usually I'd throw a new o2 at it and see what shakes out, but because of the long list, I'd like some input.
I'm thinking an evap leak somewhere on the top of the motor causing all of these problems - but not sure how the EGR code would tie in.
Any thoughts?
Vehicle gives no other indications of problems.
2009 PBM G8 GT
Pat G 218/226 & TSP Dual 660s, ARP Bits, DSteck Tuned, Magnacharger Chrome 2300 1:1, RCR Ported/Polished TB, Blower, & L92 Heads w/ LS3 intake valves, Smith Brothers Trunion Bushing Kit, ARH 1 7/8 Magnaflow MidMuff/Solo Axlebacks, RotoFab, VaporWorx PWM 1:1 fuel system, ID1050x injectors
Mike Norris Motorsports Catchcan, AEM 30-4100, JHP Boost/Fuel Gauge Pod
TSW Nurburgring Matte Gray 18" w/Nitto 555 & 555R, Satin Black SS Brembo Fronts, BMR Trailing Arms, Pedders Sway Bars, Whiteline Bushings
Gloss Black Valve Covers, 6k HID, V6 Handles, Interior/License Plate LEDs, Debadged, Holden Black Trim, Polk Dxi, GXP diffusor, a few bits from Crazy Paul
Originally Posted by TonyKarter
Anyone who has ever worked on a car has been in your position, and sitting cross-legged on a concrete floor with a dim shop light is its own kind of hell... Chalk it up as one of the rites of passage.
RIP Charlie - GRRRR8
RIP Chris Wells - Panzer Leader
-
VIP Member
Cleared codes last night and had him drive it home and around. Came back by this morning with just the following codes
p1404 - EGR
p0300 - Mult ran mis
p1404 - EGR
His Evap hadn't completed a cycle yet, so no surprise that no codes are from there.
p1404 is the same as yesterday, so we're going to throw and egr at it and see what shakes out.
2009 PBM G8 GT
Pat G 218/226 & TSP Dual 660s, ARP Bits, DSteck Tuned, Magnacharger Chrome 2300 1:1, RCR Ported/Polished TB, Blower, & L92 Heads w/ LS3 intake valves, Smith Brothers Trunion Bushing Kit, ARH 1 7/8 Magnaflow MidMuff/Solo Axlebacks, RotoFab, VaporWorx PWM 1:1 fuel system, ID1050x injectors
Mike Norris Motorsports Catchcan, AEM 30-4100, JHP Boost/Fuel Gauge Pod
TSW Nurburgring Matte Gray 18" w/Nitto 555 & 555R, Satin Black SS Brembo Fronts, BMR Trailing Arms, Pedders Sway Bars, Whiteline Bushings
Gloss Black Valve Covers, 6k HID, V6 Handles, Interior/License Plate LEDs, Debadged, Holden Black Trim, Polk Dxi, GXP diffusor, a few bits from Crazy Paul
Originally Posted by TonyKarter
Anyone who has ever worked on a car has been in your position, and sitting cross-legged on a concrete floor with a dim shop light is its own kind of hell... Chalk it up as one of the rites of passage.
RIP Charlie - GRRRR8
RIP Chris Wells - Panzer Leader
-
VIP Member
2009 PBM G8 GT
Pat G 218/226 & TSP Dual 660s, ARP Bits, DSteck Tuned, Magnacharger Chrome 2300 1:1, RCR Ported/Polished TB, Blower, & L92 Heads w/ LS3 intake valves, Smith Brothers Trunion Bushing Kit, ARH 1 7/8 Magnaflow MidMuff/Solo Axlebacks, RotoFab, VaporWorx PWM 1:1 fuel system, ID1050x injectors
Mike Norris Motorsports Catchcan, AEM 30-4100, JHP Boost/Fuel Gauge Pod
TSW Nurburgring Matte Gray 18" w/Nitto 555 & 555R, Satin Black SS Brembo Fronts, BMR Trailing Arms, Pedders Sway Bars, Whiteline Bushings
Gloss Black Valve Covers, 6k HID, V6 Handles, Interior/License Plate LEDs, Debadged, Holden Black Trim, Polk Dxi, GXP diffusor, a few bits from Crazy Paul
Originally Posted by TonyKarter
Anyone who has ever worked on a car has been in your position, and sitting cross-legged on a concrete floor with a dim shop light is its own kind of hell... Chalk it up as one of the rites of passage.
RIP Charlie - GRRRR8
RIP Chris Wells - Panzer Leader
-
Post Thanks / Like - 0 Thanks, 1 Likes, 0 Dislikes