Elusive 11's
Ran my new PB tonight in hopes of an 11 second slip. 12.02@118 with DA right at 0. I knew I should have pulled the passenger seat but still I'm pleased with the car. Stock intake and TB, stock converter, 10.8 CR, with an EPS cam, and 3.45 gears. Still rocking the Volant with Camaro 20s up front and ET streets on gto 17s.
Phillip M.
09.5 SBM GT Sports/Premium/Roof
Engine: Stock Bottom End
Heads: Stock, LS3 Intake, LY6 Exhaust, Milled
Cam: BTR IV PD
Intake: Stock Intake, Stock TB, LS7 MAF, Volant CAI
Exhaust: 1-7/8 Kooks LT's, Off-Road Pipes, Corsa cat-back
Fuel: Fore Twin Ti 450's, Vaporworx, E85, Bosch Injectors
Drivetrain: 6L80, Sonnax
Suspension: BMR 15" Strange Coilovers
Wheels/Tires: 15x10 RT-S on 275/60R15 Pro's, 17x5 Weld on M/T 28"
Ported LSA Blower, 9.55/2.55, 102 TB, Chiller
High Compression/Boost/E85
What was your 60?
Rest in Peace Charlie!
Sold
Just a GT
Originally Posted by RichsGreyGT
1.898. It leaves at about 1400rpm.
Last edited by Phil@PnP Tech; 10-25-2014 at 05:08 AM.
Phillip M.
09.5 SBM GT Sports/Premium/Roof
Engine: Stock Bottom End
Heads: Stock, LS3 Intake, LY6 Exhaust, Milled
Cam: BTR IV PD
Intake: Stock Intake, Stock TB, LS7 MAF, Volant CAI
Exhaust: 1-7/8 Kooks LT's, Off-Road Pipes, Corsa cat-back
Fuel: Fore Twin Ti 450's, Vaporworx, E85, Bosch Injectors
Drivetrain: 6L80, Sonnax
Suspension: BMR 15" Strange Coilovers
Wheels/Tires: 15x10 RT-S on 275/60R15 Pro's, 17x5 Weld on M/T 28"
Ported LSA Blower, 9.55/2.55, 102 TB, Chiller
High Compression/Boost/E85
You would have had it if you were able to hot lap it again. What is next on the mod list?
Rotohack 102 intake - 102 MAF - TPIS 102 TB - TVS1900 ported & plated w 8 rib 2.5" front + OD rear
PnP Interchiller - RCR ported heads - RCR Lunati 219/231 113+1 - Forged Bottom End
ARH 2" LT headers - Solo 3" CB - MT DRs + M&H FRs on Weld RT-S
CTS-V fuel w Vaporworx - FAST 85s - Alkycontrol meth M15 + M10 - RCR tune
9.75@139.2 ? rwhp ? rwtq
I agree with Curt. One more lap and you would have been in the 11's. Front skinnies would put you there...
Marty
G8 gone, but not forgotten...
I think a converter and skinnies are on the list. I might pull the heads for some more porting, mill another 10 thou, and go with some .040" cometics.
Then again, LSA super chargers are going for the cost of a converter...
Phillip M.
09.5 SBM GT Sports/Premium/Roof
Engine: Stock Bottom End
Heads: Stock, LS3 Intake, LY6 Exhaust, Milled
Cam: BTR IV PD
Intake: Stock Intake, Stock TB, LS7 MAF, Volant CAI
Exhaust: 1-7/8 Kooks LT's, Off-Road Pipes, Corsa cat-back
Fuel: Fore Twin Ti 450's, Vaporworx, E85, Bosch Injectors
Drivetrain: 6L80, Sonnax
Suspension: BMR 15" Strange Coilovers
Wheels/Tires: 15x10 RT-S on 275/60R15 Pro's, 17x5 Weld on M/T 28"
Ported LSA Blower, 9.55/2.55, 102 TB, Chiller
High Compression/Boost/E85
I say DO IT!
Rotohack 102 intake - 102 MAF - TPIS 102 TB - TVS1900 ported & plated w 8 rib 2.5" front + OD rear
PnP Interchiller - RCR ported heads - RCR Lunati 219/231 113+1 - Forged Bottom End
ARH 2" LT headers - Solo 3" CB - MT DRs + M&H FRs on Weld RT-S
CTS-V fuel w Vaporworx - FAST 85s - Alkycontrol meth M15 + M10 - RCR tune
9.75@139.2 ? rwhp ? rwtq
Oh hell yeah!!!
Marty
G8 gone, but not forgotten...
congrats on the new p/b wish we had that DA in Chicago lol every time I go its always in the 1000-2000 lol
Last edited by g8gtnoobie; 10-30-2014 at 04:54 PM.
show: tints, 19in vmr gunmetal 710's
go: roto fab intake/LS7maf/kooks mids/magnaflow cat back/pat G tune
Little lunati waiting to be installed
best 1/4 so far 2.04 60' 13.20 at 105.94
Posting Permissions
Reply With Quote
