-
Member
P0521 Low engine oil presure
I got this code the other day. Parked it, took it directly to the shop and they checked the oil pressure mechanically and it's all good. Im replacing the oil pressure sending unit, hopefully that's all it is. Are they notorious for going bad on these cars? Thanks in advance. Car is an 09 G8GT.
2008 IOM G8GT. Couple Bolt ons 338/349 13.408@107 with a 2.06 60' Sold
2001 C5Z06 Bolt ons 370/368 Sold
2009.5 SBM G8GT Exhaust
US Army Veteran
-
Rotohack 102 intake - 102 MAF - TPIS 102 TB - TVS1900 ported & plated w 8 rib 2.5" front + OD rear
PnP Interchiller - RCR ported heads - RCR Lunati 219/231 113+1 - Forged Bottom End
ARH 2" LT headers - Solo 3" CB - MT DRs + M&H FRs on Weld RT-S
CTS-V fuel w Vaporworx - FAST 85s - Alkycontrol meth M15 + M10 - RCR tune
9.75@139.2 ? rwhp ? rwtq
-
Member
Originally Posted by
TooManyHobbies
Yes, not unusual.
Thanks, hopefully that's all it is. No unusual noises from the car and oil pressure is normal. Just DOD doesn't work with the idiot light on.
2008 IOM G8GT. Couple Bolt ons 338/349 13.408@107 with a 2.06 60' Sold
2001 C5Z06 Bolt ons 370/368 Sold
2009.5 SBM G8GT Exhaust
US Army Veteran
-
One of our club members chased his low pressure for a bit, replacing the sender and then found out the AC Delco filter he'd used was collapsed inside.
Isn't there a screen behind the sender that can be cleaned? I seem to remember hearing about that.
2009.5 MSM GXP 500ish N/A RWHP. Mods include but aren't limited to: Texas Speed 418 (6.8L) fully forged held together with ARP from top to bottom, PRC 255cc heads, Rick Crawford intake plenum, TB port, polish and tune, Roto-Fab 102mm CAI w/LS7 MAF, Kooks 1-7/8" headers wrapped with DEI, Corsa catless system, Circle D 3200 Stall, 3.45 final drive, BMR's complete street bushing kit and sway bars, Eibach Pro Kit, G-Force Axles, running on staggered VMR 710's with Bridgestone RE11 rubber. HSV triple gauge pack with Calais smokers kit mod, V6 tails, debadge/rebadge, V6 door handles, AU black door trim, Maverick Man under hood strut covers, & washer and bolt kit, fully corrected paint thanks to Adams Polishes and my hard work. Built with reliability in mind with some power for those times when you need to pass or go over a big hill. Just a poser, not a racer!
-
Originally Posted by
Chewy
Isn't there a screen behind the sender that can be cleaned? I seem to remember hearing about that.
Yes there is a filter below the sensor that should be replaced also.
-
Post Thanks / Like - 1 Thanks, 0 Likes, 0 Dislikes
Chewy thanked for this post
-
Member
Turns out the sending unit was bad. Replaced it today.
2008 IOM G8GT. Couple Bolt ons 338/349 13.408@107 with a 2.06 60' Sold
2001 C5Z06 Bolt ons 370/368 Sold
2009.5 SBM G8GT Exhaust
US Army Veteran
-
Just did mine last weekend too.
-
Addicted Member
What part number did yall use
Sent from my SAMSUNG-SM-G900A using Tapatalk
Blown by Jessika
Tuned by Pat G
"Stock" MGM G8
-
I got the Borg Warner from O Reilly's. I didn't replace the filter.
-
Member
Originally Posted by
fengstang
What part number did yall use
Sent from my SAMSUNG-SM-G900A using Tapatalk
Ill have to go look, I am pretty sure it was the AC delco one from advance.
2008 IOM G8GT. Couple Bolt ons 338/349 13.408@107 with a 2.06 60' Sold
2001 C5Z06 Bolt ons 370/368 Sold
2009.5 SBM G8GT Exhaust
US Army Veteran