FS: Stern ST-1, 19 x 9.5, 275/35-19

[G8V8]

******SOLD****

I have 2 Stern ST-1 wheels in excl. shape in 19 x 9.5 with a 42 mm offset. They are mounted with 275/35-19 Bridgestone Potenza RE50A (not the Pole position version). The tires are very low mileage and in excl. condition. OEM TPMS sensors are included. They have been road force balanced. Pontiac center caps are included. One tire was a factory blem because of a dimple in the bead. It is hidden by the rim. They carved out the serial number. Other than that, it is perfect.

These will fit a non-lowered GT. If you are lowered, you will probably need to roll or trim the fender lips a couple of mm or so.

These have a 3" lip and the spokes are Hyperblack.

Photo from when tires were new:
http://img.villagephotos.com/p/2002-11/65524/42656743-DSCN0012_1032.JPG
http://img.villagephotos.com/p/2002-11/65524/DSCN0088_1172.JPG
http://img.villagephotos.com/p/2002-11/65524/DSCN0106_1190.JPG

I can direct you to a vendor that sells these in 19 x 8.5, 40 mm OS. These work great with the OEM sport package RE50A 245/40-19. PM for details.

$500 plus actual shipping. OBO.

[r33pwrd]

Do you have a better side shot of the car?

[-Ray-]

These won't work on my G8 unless I have the fenders rolled?

[G8V8]

Do you have a better side shot of the car?

http://img.villagephotos.com/p/2002-11/65524/DSCN0093_1177.JPG


These won't work on my G8 unless I have the fenders rolled?

If you are lowered like I am, no. My Pedders kit lowered me 1.2" in the rear. I didn't roll mine, I cut some of the lip off with a cutting disk and them cleaned it up and painted the edge. I took off about 1/8". If you are not lowered they should work. I barely rubbed before trimming.

[-Ray-]

I'll measure my height and check them against yours.
I forget how much we dropped mine.

[G8V8]

I'll measure my height and check them against yours.
I forget how much we dropped mine.

OK. I can give you a heigth from the lower rim edge to the fender lip. When I trimmed mine I put a lot of painter's tape on the lip and fender. on the lip i put the edge of the tape running pretty much down the center of the spot welds and then cut along that line. I left at least 1/2 of each spot weld intact. you only need to to trim from the line where the rear bumper meets the fender to a corresponding level on the front side. I took about 45 min to do each side. After cutting i dressed the edges with files to remove any burrs and make it nice and smooth the painted it with several coats paint. They is also a bracket used to hold the fender and bumber skin together right at the seam. There is a lot of material that is much bigger than it needs to be and it can rub so I trimmed it off too. I had never done this before but it turned out to be easy and worked great.

[G8V8]

Bump.
I can dismount the tires and sell wheels (with TPMS) and tires separately.

[done12many2]

Will these work with stock height? More specifically, if the car is launched extremely hard even at stock height, will the hard launch cause rubbing?

Thanks

[G8V8]

Will these work with stock height? More specifically, if the car is launched extremely hard even at stock height, will the hard launch cause rubbing?

Thanks

I don't know for sure. I know the rubbing on my lowered, (1.2" in the rear) was pretty minimal.

[-Ray-]

I really like the wheels Ed. I just can't bring myself to cut into my G8.

[G8V8]

The first cut is the hardest. After that you are just trying to save it! Actually it was easy and you don't need to take much off. I suspect a very minimal roll would work too.

[G8V8]

***sold***

[-Ray-]

Congrats to the buyer.