G8 Grrrr8 parts list

[Phil@PnP Tech]

Here's a real humdinger...

24432

This nut that holds the A/C lines to stud that goes into the front of the oil pan on the driver's side. Trying to find the GM part before I hit up Home Depot.

[Crazy Paul]

Nut/stud combo the same as the 4 holding down the stock fuel rails, sometimes used to retain coils onto valve covers also.
12554211
http://ecx.images-amazon.com/images/I/31DNce8nr-L.jpg

[Phil@PnP Tech]

Nut/stud combo the same as the 4 holding down the stock fuel rails, sometimes used to retain coils onto valve covers also.
12554211
http://ecx.images-amazon.com/images/I/31DNce8nr-L.jpg

Any idea what the nut would be? The stud/nut clamps down the conduit for the starter cable and then there is a nut that threads on over that to clamp down the A/C lines. I lost my nut!

[Crazy Paul]

I can't find the GM part number
It's an M6x1.0 flanged head nut
Like this
http://www.etrailer.com/p-185916.html

[Phil@PnP Tech]

Thanks for looking into this!

[STL_G8GT]

Good stuff CP!!!

[Greg@PacePerformance]

Here ya go - PN# 3530297
http://tapatalk.imageshack.com/v2/15/03/09/ff44de490a71b46eba002984a78c6b76.jpg

That was found using the thread specs from CP.

[Phil@PnP Tech]

Greg... that's what I'm after. Thank You! (And CP as well)

[TooManyHobbies]

I lost my nut! That had to hurt.

[SpaceFrank]

Finally getting around to doing some needed cosmetic work, and I need a few part numbers.

First, those black plastic plastic body clips/push rivets. Not sure if these are all different or the same type.
-Connectors that hold the front inner fender wells onto the edge of the fender
-Connectors that hold on the black front under-body panel
-Connectors that attach the bottom of the rear diffuser panel

Also, various parts on the trunk lid:
-Pontiac arrowhead emblem
-G8 GT lettering (not sure yet if I'll replace these or just remove them)
-Rear license plate light lenses
-Whatever the small black rubber/plastic pieces are that go on either side of the license plate lights, 2 per side. There may be another one right in the middle; I see a hole there in the sheet metal but nothing's in it.

Finally, what are the part numbers for the two red reflectors that go on the diffuser panel?

[Crazy Paul]

-Connectors that hold the front inner fender wells onto the edge of the fender 92138627
-Connectors that hold on the black front under-body panel 92138627
-Connectors that attach the bottom of the rear diffuser panel 92139147

Also, various parts on the trunk lid:
- Pontiac arrowhead emblem 92205490
- G8 lettering 92205488
- GT lettering 92205487
- Pontiac lettering 92205489
- Rear license plate light lens Left 92202365
- Rear license plate light lens Right 92202366
- The small black rubber/plastic pieces are that go on either side of the license plate lights, 2 per side. There may be another one right in the middle;
Rear Compartment Lid, Drain Hole Plug. 92166277

Finally, what are the part numbers for the two red reflectors that go on the diffuser panel?
- Rear Diffuser red reflector Left 92161657
- Rear Diffuser red reflector Right 92161656

[SpaceFrank]

Awesome! Thanks, Paul.

[TooManyHobbies]

There is a wiring harness plastic clamp that mounts to the drivers side of the block. I broke it when preparing to pull the engine. Somebody have the number so I can order a replacement?

[Crazy Paul]

There is a wiring harness plastic clamp that mounts to the drivers side of the block. I broke it when preparing to pull the engine. Somebody have the number so I can order a replacement?
If you can be more specific with the location then I'll try to help.
If you are talking about the cable harness that screws into the front of the left (USA drivers side) cylinder head, then I know that one.

http://i2.photobucket.com/albums/y20/PerthPurplePenguin/car%20parts/Clips/IMG_3251resized.jpg (http://s2.photobucket.com/user/PerthPurplePenguin/media/car%20parts/Clips/IMG_3251resized.jpg.html)

http://i2.photobucket.com/albums/y20/PerthPurplePenguin/car%20parts/Clips/3646TA1.jpg (http://s2.photobucket.com/user/PerthPurplePenguin/media/car%20parts/Clips/3646TA1.jpg.html)

http://i2.photobucket.com/albums/y20/PerthPurplePenguin/car%20parts/Clips/front-harness-clip800.jpg (http://s2.photobucket.com/user/PerthPurplePenguin/media/car%20parts/Clips/front-harness-clip800.jpg.html)

[TooManyHobbies]

If you can be more specific with the location then I'll try to help.
If you are talking about the cable harness that screws into the front of the left (USA drivers side) cylinder head, then I know that one.


Paul, it is not that one. This cable harness mounts to a boss on the main block itself. On the US driver side. I can't find a picture of it because all the pics I have found it is hidden behind the exhaust manifold or header. White/tan plastic thing.

[Crazy Paul]

Is it to the left or to the right of the oil drain plug in this picture?

24593

[TooManyHobbies]

Is it to the left or to the right of the oil drain plug in this picture?

24593

Unfortunately I do not have my block in my possession right now to verify it is at the machine shop). I think it is just to the right of the plug and above it.

[SpaceFrank]

- Rear license plate light lens Left 92202365
- Rear license plate light lens Right 92202366
Paul, some of the online parts suppliers are showing 92202366 (right side) as discontinued or unavailable. Everyone shows 92202365 as available. If I can't find the right-side lamp, can the left-side lamp be used on both sides?

[Crazy Paul]

If I can't find the right-side lamp, can the left-side lamp be used on both sides? Get someone to pull them both out of a car and have a look.

[Crazy Paul]

Paul, some of the online parts suppliers are showing 92202366 (right side) as discontinued or unavailable. Everyone shows 92202365 as available.
I can still get 50+ of both Part Numbers here.

Why don't you give me your complete shopping list from Post#761 (above) and I'll get everything for you?
Airfreight shipping from AU to your door will be minimal because it's all lightweight stuff. Most likely $15 for everything together.

[SpaceFrank]

Damn. Thanks for the offer, but I actually placed an order online yesterday. I got everything except the letter decals (which I'm either going to re-use or leave off) for right at $200 shipped. They are really proud of that arrowhead emblem.

[TooManyHobbies]

I can't track this one down on Nalley. The rings that go between the axles and the differential seals. I dinged one up pretty good when removing an axle. The axle was stubborn and did not want to come out.

[SpaceFrank]

- Rear license plate light lens Left 92202365
- Rear license plate light lens Right 92202366

I can now confirm that these parts are not interchangeable. They're asymmetrical and mirror images of each other. I have no idea why, but apparently even the Chevy dealer I called up shows the right side part as discontinued. There are still a few around in the states, though.

[Tommy G]

Looking for the part number for the OE rubber MAF adapter and clamp. It goes between the MAF and OE airbox and has a clamp that secures it to the MAF, with a friction fit to the airbox. This part is also reused with a Volant CAI. I have a pic but tapatalk is being ridiculous. Thanks

[Crazy Paul]

92068223 AIR MASS SENSOR ADAPTER
92068284 AIR MASS SENSOR CLAMP

http://www.iamgmparts.com/auto-parts/2008/pontiac/g8/gt-trim/6-0l-v8-gas-engine/engine-cat/air-intake-scat

[TooManyHobbies]

I can't track this one down on Nalley. The rings that go between the axles and the differential seals. I dinged one up pretty good when removing an axle. The axle was stubborn and did not want to come out.

Since I cannot seem to buy one of these I just beat the dinged one back into shape. The inside and outside are as round as the other one now. Also flat. A little waviness in the middle where I do not think it matters. Got rid of the roughness with a wire brush on the dremel.

[ft2lewis]

the silver part that goes around the top of the center console cup holders. mine snapped a month ago. also the ring around the rear driver side door speaker.

[Crazy Paul]

the silver part that goes around the top of the center console cup holders. mine snapped a month ago.
Can't be bought separately from the complete cupholder. Cupholder Part No is 92171506.
The twin ring silver piece you are looking for is definitely not Part Number 92172601, 92172601 is a figure 8 rubber insert mat which goes inside the cupholder.


also the ring around the rear driver side door speaker.
Can't be bought separately from the complete interior door panel. There is no part number for any of the round rings around speakers.

[ft2lewis]

Awesome, thanks for the help. I almost made that mistake with the liner last week

[Crazy Paul]

Awesome, thanks for the help. I almost made that mistake with the liner last week
It's a very common McSteak.

[ft2lewis]

Do you know where I can find it. The part has been discontinued?

[Crazy Paul]

Do you know where I can find it. The part has been discontinued?
Plenty available in Australia.
I'll send you a PM

[ft2lewis]

Next question, the speaker mount. I need them for all for doors. The piece that actually holds the speaker and gets mounted between the door and door trim. Also will that directly hold aftermarket speakers?

[Crazy Paul]

92158097 FRONT DR SPEAKER MOUNT BRACKET, RIGHT
 
92158096 FRONT DR SPEAKER MOUNT BRACKET, LEFT
     
92203419 REAR DR SPEAKER MOUNT BRACKET, RIGHT
 
92203418 REAR DR SPEAKER MOUNT BRACKET, LEFT

You'll just have to suck it and see with Aftermarket speakers trying to fit into stock parts.


 

[ft2lewis]

Cp would you be able to set me up with all four???

[Crazy Paul]

Cp would you be able to set me up with all four???
Yes I'll let you know in a day or so. They're not showing in stock here locally, so I'll find out what the story is and report back.

[Crazy Paul]

Cp would you be able to set me up with all four???
Yes, there's more than 6 of each part available to me from Holdens main store. I'll send you a PM

[ws98ta]

Looking for part number for short trans cooler lines that go from radiator and end at crossmember in front of engine.

[-Ray-]

Looking for part number for short trans cooler lines that go from radiator and end at crossmember in front of engine.

PIPE. Transmission Oil Cooler: Drivers side 92191948
PIPE. Transmission Oil Cooler: Pass side 92191949

Approx: $65.00 each

[astynx]

Just wanted to verify GM 92228638. Is this the 'Atari Guage' display. After all these years I may finally acquire, have programmed, and install. Thanks. Hopefully someone sees this. I seem to have lost the ability to have my posts go to "New Posts"

[Rbarganier]

Supposedly 92228638, 92217146, 92219491 these parts numbers are for the 2 gauge set and 92228599 is the three gauge from GM I personally have 92228638, 92217146, and both are 2 gauge

[astynx]

Thanks for the reply. I believe WhiteAutoMedia can (re)program 92228638 and make it have a three gauge display. I g___gled GM 92228599 nothing pertaining to a gauge display came up.

[Rbarganier]

He can he just did one of mine great Guy! I will say buy new and you save from him

Sent from my SM-G900T using Tapatalk

[astynx]

Thanks again. back in the day it seemed these displays weren't readily available. Now gm online sources they have them.

[Rbarganier]

Just know you will still need to order 92182437 its the wire harness for the Atari gauges

[Danny Juarez]

I think I have your g8
I bought it from a guy in New Orleans named scott

[rauch]

Anyone happen to know if it is possible to obtain the honeycomb for the hood scoops by themselves? I really have no urge to purchase the whole setup.

Worst case scenario, I pull the mesh out and make the scoop functional? Maybe cool down the LSA IATs some.

[SpaceFrank]

Is there a part number for the engine harness connector that attaches to the coolant temp sensor? 2008 G8 GT. The sensor itself is 12608814, but I need a replacement plug to splice into the harness. Apparently the wires going into that plug got pinched back when I did my engine swap, and the damage is too close to the connector to easily repair. My temp gauge is on the fritz, and the radiator fan doesn't always come on when it's supposed to.

[Crazy Paul]

Frank, try this repair harness.
For L76 engine.
GM Part Number 88987993
might also be AC Delco PT 1798

[SpaceFrank]

Thanks, Paul! That looks like it.

[jcmGT]

rock auto
STANDARD MOTOR PRODUCTS HP3840
https://www.rockauto.com/info/154/HP3840_PRIMARY__ra_t.jpg
STANDARD MOTOR PRODUCTS TX3A
https://www.rockauto.com/info/154/TX3Aphoto%20primary__ra_t.jpg
AIRTEX / WELLS 1P1006
https://www.rockauto.com/info/903/1P1006__ra_t.jpg
ACDELCO PT1798
https://www.rockauto.com/info/316/PT1798_Primary__ra_t.jpg

[SpaceFrank]

I'm looking for the part number for the plastic trim piece behind the center console, just above the rear A/C vents. Two of the lock tabs on mine are broken, so it won't stay in place.

Also, what about the adjuster/slider for the rear A/C vent, or whatever larger assembly would need to be replaced if the individual piece isn't available. My rear vents are kinda sticky, and I assume someone accidentally pulled one of the sliders off trying to adjust the vent.

[Greg@PacePerformance]

What color is your interior piece? Black or the silver?
Black - 92178095 - Discontinued
Silver - 92176856 - Discontinued, but call Vintage Parts @ 877-846-8243

Rear vent outlet assembly
92215166 - $35.23

-Greg

[SpaceFrank]

It's the black one. The online GM parts dealers have it listed... for $59.69!!! Holy hell.

[Greg@PacePerformance]

It's the black one. The online GM parts dealers have it listed... for $59.69!!! Holy hell.
No GM dealer in the US has one in stock, so good luck if you try and order one somewhere.

-Greg

[MongosG8]

It's the black one. The online GM parts dealers have it listed... for $59.69!!! Holy hell.

If you can find one ..get it. Soon a lot of things will be discontinued

[ScottDawe]

Rey: I'm looking for the mechanism that the door handle (drivers door) attaches to. Inside the door. It appears that mine is worn and ready to break.

I went to the dealer and got a diagram. Is there a diagram available when we are looking for parts?
Anyway, the dealer said it is part #3 on the diagram HE11A480, and it is called a housing Part # 092263003 ($50).
the handle is part #7 - 092214647 ($154) . This is for the drivers side.

[Greg@PacePerformance]

The handle attaches to rods that attach to the lock mechanism part number 92290820

[Markmsf3]

Time to stay up on the fb classified pages. There's one being parted out every week or two.

[TonyKarter]

Holden protective headlight cover?

[ah555666]

CP , can you still get the shift boot in red? Manual transmission.. What's the cost, shipping time, pay preference?

[MongosG8]

CP , can you still get the shift boot in red? Manual transmission.. What's the cost, shipping time, pay preference?

Sorry to say ..CP "Crazy Paul" is now retired.

[GXPaycheck]

Bump for clip part # info. Glad this thread is still here :thumbsup:

PS, I miss CP. :cheers:

[tchr49]

Bump for clip part # info. Glad this thread is still here :thumbsup:

PS, I miss CP. :cheers:

Second that...
I think we all do.

[-Ray-]

Bump for clip part # info. Glad this thread is still here :thumbsup:

PS, I miss CP. :cheers:

CP wasn't the only one who worked on this.

[tchr49]

CP wasn't the only one who worked on this.

Absolutely