PDA

View Full Version : Fuel line routing with Lonnie pump


wreckwriter
01-16-2011, 04:20 PM
So, for those of you with Lonnie's or other aftermarket fuel systems, where did you route your line(s)? I was going to route along the frame rail on the passenger side but I took off the inner fenderwell on the side and there's no nice route into engine compartment like there is on driver's side.

Fuel line needs to exit tank area on passenger side. I guess I could come across at front of tank and go up on driver's side? Anyone got a better idea?
wreckwriter
01-16-2011, 05:07 PM
Coming across at the back won't work well. How can I get in on the passenger side?

Sent from my DROID2 using Tapatalk
gr8lover
01-17-2011, 06:39 AM
Go "inside" frame rail and up inside passenger side wheel well and in.... I will try to get better pics this week... it works out really good...(ps... I havent forgotten about the bracket info also..hopefully by the end of the week!!!) I will get some close-ups on where it can enter..
wreckwriter
01-17-2011, 07:13 AM
Thanks!
Daniel Linnett
01-17-2011, 09:35 AM
I just followed factory lines. I am sure for certification you have to do alot more then I did.
gr8lover
01-19-2011, 03:33 AM
I wont be able to get more pics till next week........
wreckwriter
02-04-2011, 08:20 AM
Everybody cross your fingers, toes, and eyes; getting ready to fire it up..............
Daniel Linnett
02-04-2011, 08:31 AM
glad to hear you are finally getting her going again. Let us know how it goes. I have to run another vent from my sump to the tank as the return from the regulator is over pressurizing my little sump tank. I think another -10 line from the surge to stock tank will handle the increase flow :D
wreckwriter
02-04-2011, 08:35 AM
Haven't started it yet. Following Aeromotive's instruction to try and prime it. Not getting much pressure, less than 10 psi. I'm assuming the lines are full of air?
Daniel Linnett
02-04-2011, 09:32 AM
You are taking more percaution then I did lol. I turned the key to on a couple of times to prime it and the turned it to start :D
wreckwriter
02-04-2011, 10:12 AM
Yea, that's what I ended up doing too. Its all good now.
Daniel Linnett
02-04-2011, 10:55 AM
so when do we get some new dyno numbers, track slips, or videos!!
wreckwriter
02-04-2011, 11:09 AM
Its dead of winter here and I lost my job yesterday. May be a while.
G8GT721
02-04-2011, 11:15 AM
Sorry to hear that wreck


Sent from my iPhone using Tapatalk
Daniel Linnett
02-04-2011, 11:29 AM
Sorry to hear that man :( Yeah we are not used to having winter down here. we actually have 6" of snow on the ground right now. I am pissed because I had a track day scheduled tomorrow. Oh well maybe next weekend.
locrzn#92
02-04-2011, 01:02 PM
What did you do wreck as far as employment? Sorry to hear you lost your job and hopefully you can get something lined up pretty soon. Glad to hear you got it fired up.
Tempest2000
02-04-2011, 06:29 PM
Sorry to hear about the job. Hopefully you will fine something soon.

Can you snap a few pics of how you ran the lines?
gr8lover
02-04-2011, 07:04 PM
Sorry to hear about the job! Good to hear about the car.... good luck with both!!!
99-LS1-SS
02-04-2011, 07:10 PM
Damn Tom. Sorry to read about you losing your job. Hopefully it's a quick transition.
VegasNate
02-04-2011, 07:20 PM
Damn Tom. Sorry to read about you losing your job. Hopefully it's a quick transition.

^ this
STL_G8GT
02-04-2011, 08:56 PM
^ this X3
travis gore
02-05-2011, 03:41 AM
sorry to hear about your job Tom
BigV8
02-05-2011, 05:23 AM
Glad to hear the car doing good, sorry to hear about the job. Good luck to you to find another one.
wreckwriter
02-05-2011, 09:34 AM
Thanks guys. I honestly didn't like the job anyway. Job was fine but my supervisors never cared for me and, of course, I didn't care for them. Pay was ok but not great. Biggest loss is insurance.
STL_G8GT
02-06-2011, 08:23 AM
If you dont mind my asking, what did you do?


Thanks guys. I honestly didn't like the job anyway. Job was fine but my supervisors never cared for me and, of course, I didn't care for them. Pay was ok but not great. Biggest loss is insurance.
wreckwriter
02-06-2011, 08:36 AM
If you dont mind my asking, what did you do?

I.T. Help desk.
1ChargedG8
02-06-2011, 10:57 AM
I.T. Help desk.

I work for a company called Berico Technologies, our HQ is in Virginia. You might want to look on our web site www.bericotechnologies.com, as far as i know we are looking for IT/Systems people and software developers. PM'me if you want and i can give you more details about the company.

Alex